Search Results

Search found 3536 results on 142 pages for '9 04'.

Page 118/142 | < Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >

  • Mac Os X 10.7 + PHP OCI8 + MAMP PRO

    - by Mike
    i followed this article: http://www.enavigo.com/2012/01/04/enabling-oracle-oci8-php-extension-on-os-x-snow-leopard/ and im getting this error: Error 324 (net::ERR_EMPTY_RESPONSE): The server closed the connection without sending any data. Anytime i try to connect to an oracle database using OCI8. I'm not sure that oci8 is install properly. Can someone provide steps for installation of OCI8 using Mamp Pro?

    Read the article

  • iSCSI timeouts under high load

    - by Antonio
    I have two servers connected via Gigabit Ethernet. One is iSCSI target, the second one is initiator. When I run mkfs.ext4 at initiator, after a while disk IO slows down critically. In the target host I can see the following in syslog: Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668c 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668c 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668d 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668d 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119668e 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119668e 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 1196696 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 1196696 6 Sep 14 09:40:03 sh11 tgtd: abort_task_set(1139) found 119669e 0 Sep 14 09:40:03 sh11 tgtd: abort_cmd(1115) found 119669e 6 Sep 14 09:40:04 sh11 tgtd: abort_task_set(1139) found 119669f 0 Sep 14 09:40:04 sh11 tgtd: abort_cmd(1115) found 119669f 6 And load average grows to 12 or even more: # uptime 12:37:00 up 23 days, 13:25, 1 user, load average: 12.00, 7.00, 4.00 CentOS 6.3 tgtd 1.0.24 Intel Pentium 4 2.4GHz 1Gb RAM 2Tb WD Cavlar Green SATA 2.0 #lspci 00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 02) 00:01.0 PCI bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE Host-to-AGP Bridge (rev 02) 00:1d.0 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 02) 00:1d.1 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 02) 00:1d.2 USB controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 02) 00:1d.7 USB controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 02) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 82) 00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 02) 00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 02) 00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 02) 00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 02) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV200 QW [Radeon 7500] 02:01.0 Ethernet controller: D-Link System Inc DGE-530T Gigabit Ethernet Adapter (rev 11) (rev 11) 02:02.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE/SATA Controller (rev 50) 02:03.0 RAID bus controller: VIA Technologies, Inc. VT6421 IDE/SATA Controller (rev 50) 02:04.0 RAID bus controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02) 02:08.0 Ethernet controller: Intel Corporation 82801DB PRO/100 VE (CNR) Ethernet Controller (rev 82) Is there a way to tune target host to avoid these timeouts?

    Read the article

  • Mac Os X 10.7 + PHP OCI8 + MAMP PRO + ERR_EMPTY_RESPONSE

    - by gorelative
    i followed this article: http://www.enavigo.com/2012/01/04/enabling-oracle-oci8-php-extension-on-os-x-snow-leopard/ and im getting this error: Error 324 (net::ERR_EMPTY_RESPONSE): The server closed the connection without sending any data. Anytime i try to connect to an oracle database using OCI8. I'm not sure that oci8 is install properly. Can someone provide steps for installation of OCI8 using Mamp Pro?

    Read the article

  • VMware Workstation reboot 32-bit host when starting 32/64-bit guest using VT-x

    - by Powerman
    I'm trying to start 64-bit guest (MacOSX and Windows7) on 32-bit host (Hardened Gentoo Linux, kernel 2.6.28-hardened-r9) using VMware Workstation (6.5.3.185404 and 7.0.1.227600). If VT-X disabled in BIOS, VMware refuse to start 64-bit guest (as expected). If VT-X enabled in BIOS, VMware start guest without complaining, but then, in about a second (I suppose as soon as guest try to switch on 64-bit) my host reboots (actually, it's more like reset - normal reboot procedure skipped and BIOS POST start immediately). My hardware is Core 2 Duo 6600 on ASUS P5B-Deluxe with latest stable BIOS 1101. I've power-cycled system, then enabled Vanderpool in BIOS. My CPU doesn't support Trusted Execution Technology, and there no way to disable it in BIOS. I've rebooted several times after that, sometimes with power-cycled, and ensure Vandertool is enabled in BIOS. I've also run VMware-guest64check-5.5.0-18463 tool, and it report "This host is capable of running a 64-bit guest operating system under this VMware product.". About a year ago I tried to disable hardened in kernel to ensure this isn't because of PaX/GrSecurity, but that doesn't help. I have not checked 32-bit guests with VT-X enabled yet, but without VT-X they works ok. ASUS provide "beta" BIOS updates, but according to their descriptions these updates doesn't fix this issue, so I'm not sure is it good idea to try it. My best guess now it's motherboard/BIOS bug. Any ideas? Update 1: I've tried to boot vt.iso provided at http://communities.vmware.com/docs/DOC-8978 and here is it report: CPU 0: VT is enabled on this core CPU 1: VT is enabled on this core Update 2: I've just tried to boot 32-bit guests (Windows7, Ubuntu9.04 and Gentoo) using all possible virtualization modes. In Automatic, Automatic with Replay, Binary translation everything works, in Intel VT-x/EPT or AMD-V/RVI I got message "This host does not support EPT. Using software virtualization with a software MMU." and everything works. BUT in Intel VT-x or AMD-V mode all 32-bit guests reset host just like 64-bit guests! So, this issue is not specific to 64-bit guests. One more thing. Using Intel VT-x or AMD-V mode for both 32/64-bit guests my host reset right after starting VM, i.e. before VM BIOS POST and before guest even start booting. But using Intel VT-x/EPT or AMD-V/RVI VM BIOS runs ok, then 64-bit guests start booting (Windows7 completed "Loading files" progressbar), and only after that host reset.

    Read the article

  • should i bother to block these- rather lame attempt at hacking my server

    - by The Journeyman geek
    I'm running a LAMP stack, with no phpmyadmin (yes) installed. While poking through my apache server longs i noticed things like. 74.208.75.29 - - [16/Mar/2010:02:53:45 +0800] "POST http://74.208.75.29:6667/ HTTP/1.0" 404 481 "-" "-" 74.208.75.29 - - [16/Mar/2010:02:53:45 +0800] "CONNECT 74.208.75.29:6667 HTTP/1.0" 405 547 "-" "-" 66.184.178.58 - - [16/Mar/2010:13:27:59 +0800] "GET / HTTP/1.1" 200 1170 "-" "Mozilla/4.0 (compatible; MSIE 5.5; Windows 98)" 200.78.247.148 - - [16/Mar/2010:15:26:05 +0800] "GET /w00tw00t.at.ISC.SANS.DFind:) HTTP/1.1" 400 506 "-" "-" 206.47.160.224 - - [16/Mar/2010:17:27:57 +0800] "GET / HTTP/1.1" 200 1170 "-" "Mozilla/4.0 (compatible; MSIE 5.5; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:02 +0800] "GET //phpmyadmin/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 480 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:03 +0800] "GET //pma/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 476 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:04 +0800] "GET //admin/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 478 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:05 +0800] "GET //dbadmin/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 479 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:05 +0800] "GET //mysql/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 479 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" 190.220.14.195 - - [17/Mar/2010:01:28:06 +0800] "GET //php-my-admin/config/config.inc.php?p=phpinfo(); HTTP/1.1" 404 482 "-" "Mozilla/4.0 (compatible; MSIE 6.0; Windows 98)" What exactly is happening? is it a really lame attempt at hacking in? Should i bother blocking the ip addresses these are from, or just leave it?

    Read the article

  • Configuring VLAN's on two HP procurve switches

    - by pan
    Trying to route a new ISP (Microwave link) from one of my out buildings to my computer room and hence my firewall. Old ISP came direct into firewall. In the outbuilding the Microwave modem connects with cat5 to HP Procurve 2524 switch. Because this ISP is coming through my internal network, I plan on using a new vlan called "airspeed" only for this ISP traffic. Up until now I've just been using the Default_vlan on both HP switches (4108 + 2524). So far I've been unable to ping from my laptop to the ISP modem both of which are on the new vlan 2 ("Airspeed"). No traffic needs to cross from vlan 2 to vlan 1 so I've left the ports as untagged. I've used the subnet provide from my ISP as the new vlan 2 subnet. Can anybody see what I'm doing wrong here? I've added the configuration of both switch below. Rough diagram: Microwave modem (Gateway IP 77.75.00.49) | HP 2524 switch (port 24) | HP 2524 switch fibre link | HP 4108GL switch fibre link | HP 4108GL switch (port D1) | Laptop configured with IP 77.75.00.50 (for testing but will be connected to firewall) And my 4108GL config: ; J4865A Configuration Editor; Created on release #G.07.21 hostname "HP ProCurve Switch 4108GL" cdp run module 1 type J4864A module 2 type J4862B module 3 type J4862B module 4 type J4862B ip default-gateway 128.1.146.50 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged A1-A3,B1-B24,C1-C24,D2-D24 ip address 128.1.146.203 255.255.0.0 no untagged D1 exit vlan 2 name "Airspeed" untagged D1 ip address 77.75.00.51 255.255.255.248 exit Finally my 2524 config: ; J4813A Configuration Editor; Created on release #F.04.08 hostname "HP ProCurve Switch 2524" cdp run ip default-gateway 0.0.0.0 snmp-server community "public" Unrestricted snmp-server host 128.1.146.51 "public" Not-INFO snmp-server host 128.1.146.51 "public" snmp-server host 128.1.146.38 "public" vlan 1 name "DEFAULT_VLAN" untagged 1-23,25-26 no untagged 24 ip address 128.1.146.204 255.255.0.0 exit vlan 2 name "Airspeed" untagged 24 ip address 77.75.00.51 255.255.255.248 exit no aaa port-access authenticator active

    Read the article

  • Graphics driver for ubuntu on dell latitude XT

    - by marc.riera
    Hi, we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

    Read the article

  • Nginx Password Protect Directory Downloads Source Code

    - by Pamela
    I'm trying to password protect a WordPress login page on my Nginx server. When I navigate to http://www.example.com/wp-login.php, this brings up the "Authentication Required" prompt (not the WordPress login page) for a username and password. However, when I input the correct credentials, it downloads the PHP source code (wp-login.php) instead of showing the WordPress login page. Permission for my htpasswd file is set to 644. Here are the directives in question within the server block of my website's configuration file: location ^~ /wp-login.php { auth_basic "Restricted Area"; auth_basic_user_file htpasswd; } Alternately, here are the entire contents of my configuration file (including the above four lines): server { listen *:80; server_name domain.com www.domain.com; root /var/www/domain.com/web; index index.html index.htm index.php index.cgi index.pl index.xhtml; error_log /var/log/ispconfig/httpd/domain.com/error.log; access_log /var/log/ispconfig/httpd/domain.com/access.log combine$ location ~ /\. { deny all; access_log off; log_not_found off; } location = /favicon.ico { log_not_found off; access_log off; } location = /robots.txt { allow all; log_not_found off; access_log off; } location /stats/ { index index.html index.php; auth_basic "Members Only"; auth_basic_user_file /var/www/web/stats/.htp$ } location ^~ /awstats-icon { alias /usr/share/awstats/icon; } location ~ \.php$ { try_files /b371b8bbf0b595046a2ef9ac5309a1c0.htm @php; } location @php { try_files $uri =404; include /etc/nginx/fastcgi_params; fastcgi_pass unix:/var/lib/php5-fpm/web11.sock; fastcgi_index index.php; fastcgi_param SCRIPT_FILENAME $document_root$fastcgi_script_name; fastcgi_intercept_errors on; } location / { try_files $uri $uri/ /index.php?$args; client_max_body_size 64M; } location ^~ /wp-login.php { auth_basic "Restricted Area"; auth_basic_user_file htpasswd; } } If it makes any difference, I'm using Ubuntu 14.04.1 LTS with Nginx 1.4.6 and ISPConfig 3.0.5.4p3.

    Read the article

  • Help with Windows 7 BSOD with windbg minidump !analyze -v results

    - by Kurt Harless
    Hi gang, Windows 7 X64 Ultimate is BSODing occasionally. I suspect an overheating issue or something related to the use of my GTX-295 card that runs very hot. Here is an !analyze -v listing of the most recent minidump. Any and all help greatly appreciated. Kurt Microsoft (R) Windows Debugger Version 6.12.0002.633 AMD64 Copyright (c) Microsoft Corporation. All rights reserved. Loading Dump File [C:\Windows\Minidump\122810-31387-01.dmp] Mini Kernel Dump File: Only registers and stack trace are available Symbol search path is: SRV*c:\websymbols*http://msdl.microsoft.com/download/symbols Executable search path is: Windows 7 Kernel Version 7600 MP (8 procs) Free x64 Product: WinNt, suite: TerminalServer SingleUserTS Built by: 7600.16617.amd64fre.win7_gdr.100618-1621 Machine Name: Kernel base = 0xfffff800`03065000 PsLoadedModuleList = 0xfffff800`032a2e50 Debug session time: Tue Dec 28 11:04:03.597 2010 (UTC - 7:00) System Uptime: 2 days 2:28:40.407 Loading Kernel Symbols ............................................................... ................................................................ .............................................. Loading User Symbols Loading unloaded module list ................ ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* Use !analyze -v to get detailed debugging information. BugCheck 3B, {c0000005, fffff800033b8873, fffff8800e322dc0, 0} Probably caused by : ntkrnlmp.exe ( nt!RtlCompareUnicodeStrings+c3 ) Followup: MachineOwner --------- 1: kd> !analyze -v ******************************************************************************* * * * Bugcheck Analysis * * * ******************************************************************************* SYSTEM_SERVICE_EXCEPTION (3b) An exception happened while executing a system service routine. Arguments: Arg1: 00000000c0000005, Exception code that caused the bugcheck Arg2: fffff800033b8873, Address of the instruction which caused the bugcheck Arg3: fffff8800e322dc0, Address of the context record for the exception that caused the bugcheck Arg4: 0000000000000000, zero. Debugging Details: ------------------ EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s. FAULTING_IP: nt!RtlCompareUnicodeStrings+c3 fffff800`033b8873 488b7c2418 mov rdi,qword ptr [rsp+18h] CONTEXT: fffff8800e322dc0 -- (.cxr 0xfffff8800e322dc0) rax=0000000000000041 rbx=fffff8a015a3c1c0 rcx=0000000000000024 rdx=0000000000000003 rsi=fffff8800e3238b0 rdi=0000000000000009 rip=fffff800033b8873 rsp=fffff8800e323798 rbp=000000000000000d r8=fffff8a018cb374c r9=000000200a98fdc4 r10=fffff8800e323988 r11=fffff8800e32398e r12=fffff8a018127c18 r13=fffff8800126e550 r14=0000000000000001 r15=fffffa800abe1570 iopl=0 nv up ei pl nz ac po nc cs=0010 ss=0018 ds=002b es=002b fs=0053 gs=002b efl=00010216 nt!RtlCompareUnicodeStrings+0xc3: fffff800`033b8873 488b7c2418 mov rdi,qword ptr [rsp+18h] ss:0018:fffff880`0e3237b0=???????????????? Resetting default scope CUSTOMER_CRASH_COUNT: 1 DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT BUGCHECK_STR: 0x3B PROCESS_NAME: ccSvcHst.exe CURRENT_IRQL: 0 LAST_CONTROL_TRANSFER: from 0000000000000000 to fffff800033b8873 STACK_TEXT: fffff880`0e323798 00000000`00000000 : 00000000`00000000 00000000`00000000 00000000`00000000 00000000`00000000 : nt!RtlCompareUnicodeStrings+0xc3 FOLLOWUP_IP: nt!RtlCompareUnicodeStrings+c3 fffff800`033b8873 488b7c2418 mov rdi,qword ptr [rsp+18h] SYMBOL_STACK_INDEX: 0 SYMBOL_NAME: nt!RtlCompareUnicodeStrings+c3 FOLLOWUP_NAME: MachineOwner MODULE_NAME: nt IMAGE_NAME: ntkrnlmp.exe DEBUG_FLR_IMAGE_TIMESTAMP: 4c1c44a9 STACK_COMMAND: .cxr 0xfffff8800e322dc0 ; kb FAILURE_BUCKET_ID: X64_0x3B_nt!RtlCompareUnicodeStrings+c3 BUCKET_ID: X64_0x3B_nt!RtlCompareUnicodeStrings+c3 Followup: MachineOwner ---------

    Read the article

  • ubuntu mail server settings and /etc/hosts file

    - by mbrc
    This is my /etc/hosts file 127.0.0.1 localhost.localdomain localhost 127.0.1.1 ubuntu-server.xx.com ubuntu-server 193.77.xx.xx mail.xx.com mail # The following lines are desirable for IPv6 capable hosts ::1 ip6-localhost ip6-loopback fe00::0 ip6-localnet ff00::0 ip6-mcastprefix ff02::1 ip6-allnodes ff02::2 ip6-allrouters is this correct configuration for my mail server. I am behind router so i don't know if is ok to use my IP for mail.xx.com and 127.0.0.1 for localhost problem is that i can receive mail but when i send it i get Oct 17 21:29:32 ubuntu-server postfix/smtpd[2453]: warning: SASL authentication failure: Password verification failed Oct 17 21:29:32 ubuntu-server postfix/smtpd[2453]: warning: my.router[192.168.1.1]: SASL PLAIN authentication failed: authentication failure Oct 17 21:29:34 ubuntu-server postfix/smtpd[2453]: warning: my.router[192.168.1.1]: SASL LOGIN authentication failed: authentication failure EDIT: mabye is problem some port. i foward this ports. POP3 - port 110 IMAP - port 143 SMTP - port 25 HTTP - port 80 Secure SMTP (SSMTP) - port 465 Secure IMAP (IMAP4-SSL) - port 585 StartTLS - port 587 IMAP4 over SSL (IMAPS) - port 993 Secure POP3 (SSL-POP) - port 995 postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix content_filter = amavis:[127.0.0.1]:10024 delay_warning_time = 4h disable_vrfy_command = yes inet_interfaces = all inet_protocols = all mailbox_size_limit = 0 maximal_backoff_time = 8000s maximal_queue_lifetime = 7d message_size_limit = 0 minimal_backoff_time = 1000s mydestination = myhostname = mail.xx.com mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mynetworks_style = host myorigin = /etc/mailname readme_directory = no receive_override_options = no_address_mappings recipient_delimiter = + relayhost = smtp_helo_timeout = 60s smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name smtpd_client_restrictions = reject_rbl_client sbl.spamhaus.org, reject_rbl_client blackholes.easynet.nl, reject_rbl_client dnsbl.njabl.org smtpd_data_restrictions = reject_unauth_pipelining smtpd_delay_reject = yes smtpd_hard_error_limit = 12 smtpd_helo_required = yes smtpd_helo_restrictions = permit_mynetworks, warn_if_reject reject_non_fqdn_hostname, reject_invalid_hostname, permit smtpd_recipient_limit = 16 smtpd_recipient_restrictions = reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_non_fqdn_recipient, reject_unknown_recipient_domain, reject_unauth_destination, permit smtpd_sasl_auth_enable = yes smtpd_sasl_local_domain = smtpd_sasl_security_options = noanonymous smtpd_sender_restrictions = permit_sasl_authenticated, permit_mynetworks, warn_if_reject reject_non_fqdn_sender, reject_unknown_sender_domain, reject_unauth_pipelining, permit smtpd_soft_error_limit = 3 smtpd_tls_cert_file = /etc/ssl/private/mail.xx.com.crt smtpd_tls_key_file = /etc/ssl/private/mail.xx.com.key smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes unknown_local_recipient_reject_code = 450 virtual_alias_maps = mysql:/etc/postfix/maps/alias.cf virtual_gid_maps = static:5000 virtual_mailbox_base = /var/spool/mail/virtual virtual_mailbox_domains = mysql:/etc/postfix/maps/domain.cf virtual_mailbox_limit = 0 virtual_mailbox_maps = mysql:/etc/postfix/maps/user.cf virtual_uid_maps = static:5000 saslfinger -c version: 1.0.4ostfix Cyrus sasl configuration Ä mode: client-side SMTP AUTH -- basics -- Postfix: 2.9.3 System: Ubuntu 12.04.1 LTS \n \l -- smtp is linked to -- libsasl2.so.2 => /usr/lib/i386-linux-gnu/libsasl2.so.2 (0x00d3a000) -- active SMTP AUTH and TLS parameters for smtp -- relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes -- listing of /usr/lib/sasl2 -- total 28 drwxr-xr-x 2 root root 4096 okt 14 15:18 . drwxr-xr-x 72 root root 12288 okt 14 15:03 .. -rw-r--r-- 1 root root 1 maj 4 06:17 berkeley_db.txt -rw-r----- 1 root root 701 okt 14 15:18 saslpasswd.conf -rw-r----- 1 smmta smmsp 885 okt 14 15:18 Sendmail.conf -- listing of /etc/postfix/sasl -- total 12 drwxr-xr-x 2 root root 4096 okt 11 18:55 . drwxr-xr-x 4 root root 4096 okt 12 06:59 .. -rwx------ 1 root root 241 okt 11 18:55 smtpd.conf Cannot find the smtp_sasl_password_maps parameter in main.cf. Client-side SMTP AUTH cannot work without this parameter!

    Read the article

  • Server load spikes several times a day, load average for the past month is 5 times the load average all year

    - by AMF
    My Munin notifications set up for our (Debian) LAMP cluster have been notifying me continuously that our load on our production machine has been at dangerous levels. While the average load all year typically runs between 2 and 8, the load in the past month and only the past month -- has been skyrocketing to 10, 18, and occasionally even 50-60. The spikes last only 5-10 minutes at a time and occur about every 2-3 hours. The spikes do not effect performance only because I have a script that sends traffic off our server to a mirror CDN when the load goes above 10. I've looked for cron jobs that correlate with this timeframe but there is nothing I can see that would cause this. Site traffic is also normal (we receive about 200K visits per day). I'm also trying to think of anything I've changed around the time this problem began, and I really cannot think of anything. This is probably not much to go on. Maybe there is a clue in the top print-out (below) that I'm not seeing. How do I proceed to find the cause? -- Typical top when the load is NOT spiking: top - 11:13:09 up 472 days, 25 min, 1 user, load average: 6.08, 4.29, 3.80 Tasks: 105 total, 1 running, 104 sleeping, 0 stopped, 0 zombie Cpu(s): 41.2%us, 5.8%sy, 0.0%ni, 49.5%id, 2.7%wa, 0.1%hi, 0.7%si, 0.0%st Mem: 3369592k total, 2166980k used, 1202612k free, 559504k buffers Swap: 2650684k total, 1892k used, 2648792k free, 1129116k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 32046 apache 15 0 36300 12m 9828 S 20 0.4 0:01.97 apache2 32679 apache 15 0 36568 13m 10m S 19 0.4 0:01.69 apache2 31441 apache 15 0 36616 13m 10m S 19 0.4 0:04.13 apache2 31477 apache 15 0 36596 13m 9.8m S 15 0.4 0:01.99 apache2 31993 apache 15 0 36876 16m 12m S 12 0.5 0:02.01 apache2 31782 apache 15 0 36836 14m 10m S 8 0.4 0:02.17 apache2 32198 apache 15 0 36536 13m 10m S 7 0.4 0:01.59 apache2 880 apache 15 0 36508 9708 6236 S 7 0.3 0:00.42 apache2 31945 apache 17 0 36876 16m 13m S 5 0.5 0:03.17 apache2 32197 apache 16 0 36636 10m 7504 S 5 0.3 0:02.70 apache2 32326 apache 15 0 37024 11m 7632 S 5 0.3 0:02.15 apache2 32565 apache 15 0 37280 13m 9.8m S 5 0.4 0:03.75 apache2 32676 apache 15 0 36896 16m 12m S 4 0.5 0:00.95 apache2 32678 apache 15 0 36536 12m 9692 S 4 0.4 0:02.27 apache2 974 apache 16 0 37064 9888 6016 D 4 0.3 0:00.13 apache2 32150 apache 16 0 36832 13m 10m S 3 0.4 0:01.74 apache2 31780 apache 16 0 36848 11m 7660 S 3 0.3 0:02.87 apache2

    Read the article

  • !! 0xc01a00d !! aka Vista won't boot

    - by Chris
    Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box. One of my users has an HP DV5-1235dx laptop running Windows Vista Professional x64. Last night, our WSUS server pushed out a few updates including "Security Update for Windows Vista for x64-based Systems (KB960859)". When we try to boot the laptop today, a black screen with white text comes up displaying: xxx/169894 (something) Where xxx increments rapidly and something is some dll or registry key. Eventually that stops and the screen displays !! 0xc01a00d !! 35566/169894 (\Registry\Machine\COMPONENTS\DerivedDat...) No other computers that received this update are displaying the same error. So far I've tried running CHKDSK off of HBCD. It repaired a thing or two, but the computer still doesn't boot. I tried repairing the Windows install from the Vista CD, but I get a black screen with white text displaying something along the lines of: 0 No Emulation System Type 00 1 No Emulation System Type 00 Select one of the above Booting in Last Known Good Configuration doesn't work. Booting in Safe Mode freezes at Loading Windows Files [snip] Loaded: \windows\system32\drivers\crcdisk.sys Please wait... My next step is trying to boot Safe Mode with Command Prompt and try to run rstrui.exe. While I do that, does anybody have any guidance? Edit: Booting into Safe Mode with Command Prompt will not work. See Booting in Safe Mode above. Edit 2: I managed to boot from the Vista DVD. I ran the system repair, and now I get a black screen with white text saying: !! 0xc0000034 !! 290/169894 (_0000000000000000.cdf-ms) Edit 3: I ran the system repair again, and it attempted to repair my hard drive. It failed. Problem Signature: Problem Event Name: Startup Repair V2 Problem Signature 01: External Media Problem Signature 02: 6.0.6001.18000.6.0.6001.18000 Problem Signature 03: 4 Problem Signature 04: 196611 Problem Signature 05: CorruptVolume Problem Signature 06: NoBootFailure Problem Signature 07: 0 Problem Signature 08: 0 Problem Signature 09: unknown Problem Signature 10: 1168 OS Version: 6.0.6002.2.2.0.256.1 Locale ID: 1033 Answer: Parts of the hard drive are corrupted. All of my user's code was checked in, so I'm just going to format the box.

    Read the article

  • Why are emails sent from my applications being marked as spam?

    - by Brian
    Hi. I have 2 web apps running on the same server. The first is www.nimikri.com and the other is www.hourjar.com. Both apps share the same IP address (75.127.100.175). My server is through a shared hosting company. I've been testing my apps, and at first all my emails were being delivered to me just fine. Then a few days ago every email from both apps got dumped into my spam box (in gmail and google apps). So far the apps have just been sending emails to me and nobody else, so I know people aren't manually flagging them as spam. I did a reverse DNS lookup for my IP and the results I got were these: 100.127.75.in-addr.arpa NS DNS2.GNAX.NET. 100.127.75.in-addr.arpa NS DNS1.GNAX.NET. Should the reverse DNS lookup point to nimikri.com and hourjar.com, or are they set up fine the way they are? I noticed in the email header these 2 lines: Received: from nimikri.nimikri.com From: Hour Jar <[email protected]> Would the different domain names be causing gmail to think this is spam? Here is the header from one of the emails. Please let me know if any of this looks like a red flag for spam. Thanks. Delivered-To: [email protected] Received: by 10.231.157.85 with SMTP id a21cs54749ibx; Sun, 25 Apr 2010 10:03:14 -0700 (PDT) Received: by 10.151.130.18 with SMTP id h18mr3056714ybn.186.1272214992196; Sun, 25 Apr 2010 10:03:12 -0700 (PDT) Return-Path: <[email protected]> Received: from nimikri.nimikri.com ([75.127.100.175]) by mx.google.com with ESMTP id 28si4358025gxk.44.2010.04.25.10.03.11; Sun, 25 Apr 2010 10:03:11 -0700 (PDT) Received-SPF: neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) client-ip=75.127.100.175; Authentication-Results: mx.google.com; spf=neutral (google.com: 75.127.100.175 is neither permitted nor denied by best guess record for domain of [email protected]) [email protected] Received: from nimikri.nimikri.com (localhost.localdomain [127.0.0.1]) by nimikri.nimikri.com (8.14.3/8.14.3) with ESMTP id o3PH3A7a029986 for <[email protected]>; Sun, 25 Apr 2010 12:03:11 -0500 Date: Sun, 25 Apr 2010 12:03:10 -0500 From: Hour Jar <[email protected]> To: [email protected] Message-ID: <[email protected]> Subject: [email protected] has invited you to New Event MIME-Version: 1.0 Content-Type: text/html; charset=us-ascii Content-Transfer-Encoding: 7bit

    Read the article

  • Virtual Machine with Bridged Adapter to Centos not accepting ssh from host machine [migrated]

    - by javadba
    I have a bridged connection on VirtualBox from os/x 10.8.5 host to Centos 5.8 client. But I suspect this is more of a general issue than specific to the host and precise version of linux. Shown below are the networking info from the VirtualBox and from within the guest sshd is running on port 22: [root@oracle-linux ~]# ps -ef | grep sshd | grep -v grep root 3103 1 0 20:22 ? 00:00:00 /usr/sbin/sshd root 14994 3103 0 21:23 ? 00:00:00 sshd: root@pts/1 Port 22 listening: [root@oracle-linux ~]# netstat -an | grep 22 | grep tcp | grep LIST tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2207 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2208 0.0.0.0:* LISTEN tcp 0 0 :::22 :::* LISTEN Here are ip addresses, still on the guest os: [root@oracle-linux ~]# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b9:e5:79 brd ff:ff:ff:ff:ff:ff inet 10.0.15.100/24 brd 10.0.15.255 scope global eth0 inet6 fe80::a00:27ff:feb9:e579/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b4:86:8a brd ff:ff:ff:ff:ff:ff inet 10.0.3.15/24 brd 10.0.3.255 scope global eth1 inet6 fe80::a00:27ff:feb4:868a/64 scope link valid_lft forever preferred_lft forever [root@oracle-linux ~]# I can ssh to the guest from the guest: root@oracle-linux ~]# ssh 10.0.3.15 The authenticity of host '10.0.3.15 (10.0.3.15)' can't be established. RSA key fingerprint is ef:08:19:72:95:4d:e5:28:af:f3:6f:54:07:84:ba:04. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '10.0.3.15' (RSA) to the list of known hosts. [email protected]'s password: Last login: Mon Oct 21 21:24:12 2013 from 10.0.15.100 But can NOT ssh from the host to the guest: 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection Here is bridged connection infO; BTW I looked into other answers, and one of them mentioned doing service iptables stop That did not help. Adapter 2 is a NAT, shown below In case NAT is causing any issues, i shut it down and restarted networking. [root@oracle-linux ~]# /etc/init.d/network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: Still No joy.. 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection

    Read the article

  • Virtual Machine with Bridged Adapter to Centos not accepting ssh from host machine

    - by javadba
    I have a bridged connection on VirtualBox from os/x 10.8.5 host to Centos 5.8 client. But I suspect this is more of a general issue than specific to the host and precise version of linux. Shown below are the networking info from the VirtualBox and from within the guest sshd is running on port 22: [root@oracle-linux ~]# ps -ef | grep sshd | grep -v grep root 3103 1 0 20:22 ? 00:00:00 /usr/sbin/sshd root 14994 3103 0 21:23 ? 00:00:00 sshd: root@pts/1 Port 22 listening: [root@oracle-linux ~]# netstat -an | grep 22 | grep tcp | grep LIST tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2207 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:2208 0.0.0.0:* LISTEN tcp 0 0 :::22 :::* LISTEN Here are ip addresses, still on the guest os: [root@oracle-linux ~]# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b9:e5:79 brd ff:ff:ff:ff:ff:ff inet 10.0.15.100/24 brd 10.0.15.255 scope global eth0 inet6 fe80::a00:27ff:feb9:e579/64 scope link valid_lft forever preferred_lft forever 3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast qlen 1000 link/ether 08:00:27:b4:86:8a brd ff:ff:ff:ff:ff:ff inet 10.0.3.15/24 brd 10.0.3.255 scope global eth1 inet6 fe80::a00:27ff:feb4:868a/64 scope link valid_lft forever preferred_lft forever [root@oracle-linux ~]# I can ssh to the guest from the guest: root@oracle-linux ~]# ssh 10.0.3.15 The authenticity of host '10.0.3.15 (10.0.3.15)' can't be established. RSA key fingerprint is ef:08:19:72:95:4d:e5:28:af:f3:6f:54:07:84:ba:04. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '10.0.3.15' (RSA) to the list of known hosts. [email protected]'s password: Last login: Mon Oct 21 21:24:12 2013 from 10.0.15.100 But can NOT ssh from the host to the guest: 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection Here is bridged connection infO; BTW I looked into other answers, and one of them mentioned doing service iptables stop That did not help. Adapter 2 is a NAT, shown below In case NAT is causing any issues, i shut it down and restarted networking. [root@oracle-linux ~]# /etc/init.d/network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: Still No joy.. 18:27:04/shared:11 $ssh [email protected] ssh: connect to host 10.0.15.100 port 22: Operation timed out lost connection

    Read the article

  • Graphics driver for ubuntu on dell latitude XT

    - by marc.riera
    we have a laptop (dell latitude xt) on our company, and we would like to install ubuntu on it. windows 7 works fine out of the box, so the hardware is fine. since this laptop has a touchscreen we just installed ubuntu 10.10 netbook edition 32x. But, we do not manage to enable the touchscreen, neither the vga graphic drivers. this is the output from lspci, if somebody cares. 00:00.0 Host bridge: ATI Technologies Inc Radeon Xpress 7930 Host Bridge 00:01.0 PCI bridge: ATI Technologies Inc RS7932 PCI Bridge 00:04.0 PCI bridge: ATI Technologies Inc Device 7934 00:06.0 PCI bridge: ATI Technologies Inc RS7936 PCI Bridge 00:07.0 PCI bridge: ATI Technologies Inc Device 7937 00:13.0 USB Controller: ATI Technologies Inc SB600 USB (OHCI0) 00:13.1 USB Controller: ATI Technologies Inc SB600 USB (OHCI1) 00:13.2 USB Controller: ATI Technologies Inc SB600 USB (OHCI2) 00:13.3 USB Controller: ATI Technologies Inc SB600 USB (OHCI3) 00:13.4 USB Controller: ATI Technologies Inc SB600 USB (OHCI4) 00:13.5 USB Controller: ATI Technologies Inc SB600 USB Controller (EHCI) 00:14.0 SMBus: ATI Technologies Inc SBx00 SMBus Controller (rev 14) 00:14.1 IDE interface: ATI Technologies Inc SB600 IDE 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 00:14.3 ISA bridge: ATI Technologies Inc SB600 PCI to LPC Bridge 00:14.4 PCI bridge: ATI Technologies Inc SBx00 PCI to PCI Bridge 01:05.0 VGA compatible controller: ATI Technologies Inc Radeon Xpress 1250 03:01.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller 03:01.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller 03:01.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5756ME Gigabit Ethernet PCI Express 0b:00.0 Network controller: Broadcom Corporation BCM4321 802.11a/b/g/n (rev 03) I've tryied to install ati drivers 9.3 , which I downloaded and installed, unpacked and installed, builded and installed, but nothing worked. Looks like the latests version is just accepted to work on jaunty 9.04, so they are kind of old. what else I can do? thanks. Marc Information added: lsusb and lspci -n |grep 01:05.0 sysop@wl083517:~$ lspci -n |grep 01:05.0 01:05.0 0300: 1002:7942 sysop@wl083517:~$ lsusb Bus 006 Device 002: ID 413c:8138 Dell Computer Corp. Wireless 5520 Voda I Mobile Broadband (3G HSDPA) Minicard EAP-SIM Port Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 005 Device 002: ID 413c:8140 Dell Computer Corp. Wireless 360 Bluetooth Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 002: ID 1b96:0001 N-Trig Duosense Transparent Electromagnetic Digitizer Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 002: ID 03f0:1807 Hewlett-Packard Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub sysop@wl083517:~$

    Read the article

  • How to properly shutdown a Linux VMware Server Host

    - by Mikee
    Hi Everybody: In our lab, we have a server running Ubuntu Linux 8.04.4 x64, with VMware Server 2.1 hosting 4 VM's. I have a major concern with regards to shutting down the host server. Mostly, how do I ensure that the guest VM's are being shut down safely? In the VMware web interface console, I have enabled: "Allow virtual machines to start and stop automatically with the system" I enabled the Default Startup Delay for 15 seconds along with the "Start next VM immediately if the VMware Tools start" option checked I enabled the Default Shutdown Delay with a 60 second shutdown delay and a Shutdown Action of "Shut Down Guest" All VM's have the VMware Tools installed and properly working. All VM's are moved up into the "Specified Order" section of "Startup Order", thus when powering the server back on, all those VM's should start up again in that specified order. When I went to shut down the server, I used the shutdown -h now command. Based on the settings I entered above, I was expecting a 4 minute shutdown, as there is an option to delay the shutdown of each VM by 60 seconds. However, that is not what happened. Instead, the server shutdown in under a minute. When I powered the server back on, only 2 VM's properly loaded. The other 2 showed the following error: "Power on Virtual Machine" failed to complete If these problems problems persist, please contact your system administrator. Details: Cannot open the disk '[location to .vmdk]' or one of the snapshot disks it depends on. Reason: Failed to lock the file. Obviously, if this error occured, then it is clear to me that the VM's were not properly shutdown, or the server powered off before the VM's were completely shutdown. I have fixed the above error by deleting the .lck files in the respective VM directories. How would I know if the VM's were properly shut down? I checked the VMware-server logs, but they only seem to display the logs of when the vmware-mgmt service is running in the current session. I'm mostly running Linux VM's, so is there an easy way to know whether or not a server was properly shut down in Linux? Thank you all for the help!

    Read the article

  • open-sshd service withou pam support !! How can I add pam support to sshd? Ubuntu

    - by marc.riera
    Hi, I'm using AD as my user account server with ldap. Most of the servers run with UsePam yes except this one, it has lack of pam support on sshd. root@linserv9:~# ldd /usr/sbin/sshd linux-vdso.so.1 => (0x00007fff621fe000) libutil.so.1 => /lib/libutil.so.1 (0x00007fd759d0b000) libz.so.1 => /usr/lib/libz.so.1 (0x00007fd759af4000) libnsl.so.1 => /lib/libnsl.so.1 (0x00007fd7598db000) libcrypto.so.0.9.8 => /usr/lib/libcrypto.so.0.9.8 (0x00007fd75955b000) libcrypt.so.1 => /lib/libcrypt.so.1 (0x00007fd759323000) libc.so.6 => /lib/libc.so.6 (0x00007fd758fc1000) libdl.so.2 => /lib/libdl.so.2 (0x00007fd758dbd000) /lib64/ld-linux-x86-64.so.2 (0x00007fd759f0e000) I have this packages installed root@linserv9:~# dpkg -l|grep -E 'pam|ssh' ii denyhosts 2.6-2.1 an utility to help sys admins thwart ssh hac ii libpam-modules 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules for PAM ii libpam-runtime 0.99.7.1-5ubuntu6.1 Runtime support for the PAM library ii libpam-ssh 1.91.0-9.2 enable SSO behavior for ssh and pam ii libpam0g 0.99.7.1-5ubuntu6.1 Pluggable Authentication Modules library ii libpam0g-dev 0.99.7.1-5ubuntu6.1 Development files for PAM ii openssh-blacklist 0.1-1ubuntu0.8.04.1 list of blacklisted OpenSSH RSA and DSA keys ii openssh-client 1:4.7p1-8ubuntu1.2 secure shell client, an rlogin/rsh/rcp repla ii openssh-server 1:4.7p1-8ubuntu1.2 secure shell server, an rshd replacement ii quest-openssh 5.2p1_q13-1 Secure shell root@linserv9:~# What I'm doing wrong? thanks. Edit: root@linserv9:~# cat /etc/pam.d/sshd # PAM configuration for the Secure Shell service # Read environment variables from /etc/environment and # /etc/security/pam_env.conf. auth required pam_env.so # [1] # In Debian 4.0 (etch), locale-related environment variables were moved to # /etc/default/locale, so read that as well. auth required pam_env.so envfile=/etc/default/locale # Standard Un*x authentication. @include common-auth # Disallow non-root logins when /etc/nologin exists. account required pam_nologin.so # Uncomment and edit /etc/security/access.conf if you need to set complex # access limits that are hard to express in sshd_config. # account required pam_access.so # Standard Un*x authorization. @include common-account # Standard Un*x session setup and teardown. @include common-session # Print the message of the day upon successful login. session optional pam_motd.so # [1] # Print the status of the user's mailbox upon successful login. session optional pam_mail.so standard noenv # [1] # Set up user limits from /etc/security/limits.conf. session required pam_limits.so # Set up SELinux capabilities (need modified pam) # session required pam_selinux.so multiple # Standard Un*x password updating. @include common-password

    Read the article

  • RAID 50 24Port Fast Writes Slow Reads - Ubuntu

    - by James
    What is going on here?! I am baffled. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/dev/zero of=/Volumes/MercuryInternal/test/test.fs bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 57.0948 s, 735 MB/s serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo dd if=/Volumes/MercuryInternal/test/test.fs of=/dev/null bs=4096k count=10000 10000+0 records in 10000+0 records out 41943040000 bytes (42 GB) copied, 116.189 s, 361 MB/s OF NOTE: My RAID50 is 3 sets of 8 disks. - This might not be the best config for SPEED. OS: Ubuntu 12.04.1 x64 Hardware Raid: RocketRaid 2782 - 24 Port Controller HardDriveType: Seagate Barracuda ES.2 1TB Drivers: v1.1 Open Source Linux Drivers. So 24 x 1TB drives, partitioned using parted. Filesystem is ext4. I/O scheduler WAS noop but have changed it to deadline with no seemingly performance benefit/cost. serveradmin@FILESERVER:/Volumes/MercuryInternal/test$ sudo gdisk -l /dev/sdb GPT fdisk (gdisk) version 0.8.1 Partition table scan: MBR: protective BSD: not present APM: not present GPT: present Found valid GPT with protective MBR; using GPT. Disk /dev/sdb: 41020686336 sectors, 19.1 TiB Logical sector size: 512 bytes Disk identifier (GUID): 95045EC6-6EAF-4072-9969-AC46A32E38C8 Partition table holds up to 128 entries First usable sector is 34, last usable sector is 41020686302 Partitions will be aligned on 2048-sector boundaries Total free space is 5062589 sectors (2.4 GiB) Number Start (sector) End (sector) Size Code Name 1 2048 41015625727 19.1 TiB 0700 primary To me this should be working fine. I can't think of anything that would be causing this other then fundamental driver errors? I can't seem to get much/if any higher then the 361MB a second, is this hitting the "SATA2" link speed, which it shouldn't given it is a PCIe2.0 card. Or maybe some cacheing quirk - I do have Write Back enabled. Does anyone have any suggestions? Tests for me to perform? Or if you require more information, I am happy to provide it! This is a video fileserver for editing machines, so we have a preference for FAST reads over writes. I was just expected more from RAID 50 and 24 drives together... EDIT: (hdparm results) serveradmin@FILESERVER:/Volumes/MercuryInternal$ sudo hdparm -Tt /dev/sdb /dev/sdb: Timing cached reads: 17458 MB in 2.00 seconds = 8735.50 MB/sec Timing buffered disk reads: 884 MB in 3.00 seconds = 294.32 MB/sec EDIT2: (config details) Also, I am using a RAID block size of 256K. I was told a larger block size is better for larger (in my case large video) files. EDIT3: (Bonnie++ Results. Would love some guidance with this!)

    Read the article

  • OpenSSH does not accept public key?

    - by Bob
    I've been trying to solve this for a while, but I'm admittedly quite stumped. I just started up a new server and was setting up OpenSSH to use key-based SSH logins, but I've run into quite a dilemma. All the guides are relatively similar, and I was following them closely (despite having done this once before). I triple checked my work to see if I would notice some obvious screw up - but nothing is apparent. As far as I can tell, I haven't done anything wrong (and I've checked very closely). If it's any help, on my end I'm using Cygwin and the server is running Ubuntu 12.04.1 LTS. Anyways, here is the output (I've removed/censored some parts for privacy (primarily anything with my name, website, or its IP address), but I can assure you that nothing is wrong there): $ ssh user@host -v OpenSSH_5.9p1, OpenSSL 0.9.8r 8 Feb 2011 debug1: Connecting to host [ipaddress] port 22. debug1: Connection established. debug1: identity file /home/user/.ssh/id_rsa type 1 debug1: identity file /home/user/.ssh/id_rsa-cert type -1 debug1: identity file /home/user/.ssh/id_dsa type -1 debug1: identity file /home/user/.ssh/id_dsa-cert type -1 debug1: identity file /home/user/.ssh/id_ecdsa type -1 debug1: identity file /home/user/.ssh/id_ecdsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.9p1 Debian-5ubuntu1 debug1: match: OpenSSH_5.9p1 Debian-5ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.9 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: sending SSH2_MSG_KEX_ECDH_INIT debug1: expecting SSH2_MSG_KEX_ECDH_REPLY debug1: Server host key: ECDSA 24:68:c3:d8:13:f8:61:94:f2:95:34:d1:e2:6d:e7:d7 debug1: Host 'host' is known and matches the ECDSA host key. debug1: Found key in /home/user/.ssh/known_hosts:2 debug1: ssh_ecdsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Offering RSA public key: /home/user/.ssh/id_rsa debug1: Authentications that can continue: publickey debug1: Trying private key: /home/user/.ssh/id_dsa debug1: Trying private key: /home/user/.ssh/id_ecdsa debug1: No more authentication methods to try. Permission denied (publickey). What can I do to resolve my problem?

    Read the article

  • Postmaster uses excessive CPU and Disk Writes

    - by wolfcastle
    using PostgreSQL 9.1.2 I'm seeing excessive CPU usage and large amounts of writes to disk from postmaster tasks. This happens even while my application is doing almost nothing (10s of inserts per MINUTE). There are a reasonable number of connections open however. I've been trying to determine what in my application is causing this. I'm pretty newb with postgresql, and haven't gotten anywhere so far. I've turned on some logging options in my config file, and looked at connections in the pg_stat_activity table, but they are all idle. Yet each connection consumes ~ 50% CPU, and is writing ~15M/s to disk (reading nothing). I'm basically using the stock postgresql.conf with very little tweaks. I'd appreciate any advice or pointers on what I can do to track this down. Here is a sample of what top/iotop is showing me: Cpu(s): 18.9%us, 14.4%sy, 0.0%ni, 53.4%id, 11.8%wa, 0.0%hi, 1.5%si, 0.0%st Mem: 32865916k total, 7263720k used, 25602196k free, 575608k buffers Swap: 16777208k total, 0k used, 16777208k free, 4464212k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 17057 postgres 20 0 236m 33m 13m R 45.0 0.1 73:48.78 postmaster 17188 postgres 20 0 219m 15m 11m R 42.3 0.0 61:45.57 postmaster 17963 postgres 20 0 219m 16m 11m R 42.3 0.1 27:15.01 postmaster 17084 postgres 20 0 219m 15m 11m S 41.7 0.0 63:13.64 postmaster 17964 postgres 20 0 219m 17m 12m R 41.7 0.1 27:23.28 postmaster 18688 postgres 20 0 219m 15m 11m R 41.3 0.0 63:46.81 postmaster 17088 postgres 20 0 226m 24m 12m R 41.0 0.1 64:39.63 postmaster 24767 postgres 20 0 219m 17m 12m R 41.0 0.1 24:39.24 postmaster 18660 postgres 20 0 219m 14m 9.9m S 40.7 0.0 60:51.52 postmaster 18664 postgres 20 0 218m 15m 11m S 40.7 0.0 61:39.61 postmaster 17962 postgres 20 0 222m 19m 11m S 40.3 0.1 11:48.79 postmaster 18671 postgres 20 0 219m 14m 9m S 39.4 0.0 60:53.21 postmaster 26168 postgres 20 0 219m 15m 10m S 38.4 0.0 59:04.55 postmaster Total DISK READ: 0.00 B/s | Total DISK WRITE: 195.97 M/s TID PRIO USER DISK READ DISK WRITE SWAPIN IO> COMMAND 17962 be/4 postgres 0.00 B/s 14.83 M/s 0.00 % 0.25 % postgres: aggw aggw [local] idle 17084 be/4 postgres 0.00 B/s 15.53 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17963 be/4 postgres 0.00 B/s 15.00 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17188 be/4 postgres 0.00 B/s 14.80 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 17964 be/4 postgres 0.00 B/s 15.50 M/s 0.00 % 0.24 % postgres: aggw aggw [local] idle 18664 be/4 postgres 0.00 B/s 15.13 M/s 0.00 % 0.23 % postgres: aggw aggw [local] idle 17088 be/4 postgres 0.00 B/s 14.71 M/s 0.00 % 0.13 % postgres: aggw aggw [local] idle 18688 be/4 postgres 0.00 B/s 14.72 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 24767 be/4 postgres 0.00 B/s 14.93 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 18671 be/4 postgres 0.00 B/s 16.14 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 17057 be/4 postgres 0.00 B/s 13.58 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 26168 be/4 postgres 0.00 B/s 15.50 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle 18660 be/4 postgres 0.00 B/s 15.85 M/s 0.00 % 0.00 % postgres: aggw aggw [local] idle

    Read the article

  • Apache and MySQL taking all the memory? Maximum connections?

    - by lpfavreau
    I've a had one of our servers going down (network wise) but keeping its uptime (so looks the server is not losing its power) recently. I've asked my hosting company to investigate and I've been told, after investigation, that Apache and MySQL were at all time using 80% of the memory and peaking at 95% and that I might be needing to add some more RAM to the server. One of their justifications to adding more RAM was that I was using the default max connections setting (125 for MySQL and 150 for Apache) and that for handling those 150 simultaneous connections, I would need at least 3Gb of memory instead of the 1Gb I have at the moment. Now, I understand that tweaking the max connections might be better than me leaving the default setting although I didn't feel it was a concern at the moment, having had servers with the same configuration handle more traffic than the current 1 or 2 visitors before the lunch, telling myself I'd tweak it depending on the visits pattern later. I've also always known Apache was more memory hungry under default settings than its competitor such as nginx and lighttpd. Nonetheless, looking at the stats of my machine, I'm trying to see how my hosting company got those numbers. I'm getting: # free -m total used free shared buffers cached Mem: 1000 944 56 0 148 725 -/+ buffers/cache: 71 929 Swap: 1953 0 1953 Which I guess means that yes, the server is reserving around 95% of its memory at the moment but I also thought it meant that only 71 out of the 1000 total were really used by the applications at the moment looking a the buffers/cache row. Also I don't see any swapping: # vmstat 60 procs -----------memory---------- ---swap-- -----io---- -system-- ----cpu---- r b swpd free buff cache si so bi bo in cs us sy id wa 0 0 0 57612 151704 742596 0 0 1 1 3 11 0 0 100 0 0 0 0 57604 151704 742596 0 0 0 1 1 24 0 0 100 0 0 0 0 57604 151704 742596 0 0 0 2 1 18 0 0 100 0 0 0 0 57604 151704 742596 0 0 0 0 1 13 0 0 100 0 And finally, while requesting a page: top - 08:33:19 up 3 days, 13:11, 2 users, load average: 0.06, 0.02, 0.00 Tasks: 81 total, 1 running, 80 sleeping, 0 stopped, 0 zombie Cpu(s): 1.3%us, 0.3%sy, 0.0%ni, 98.3%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 1024616k total, 976744k used, 47872k free, 151716k buffers Swap: 2000052k total, 0k used, 2000052k free, 742596k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 24914 www-data 20 0 26296 8640 3724 S 2 0.8 0:00.06 apache2 23785 mysql 20 0 125m 18m 5268 S 1 1.9 0:04.54 mysqld 24491 www-data 20 0 25828 7488 3180 S 1 0.7 0:00.02 apache2 1 root 20 0 2844 1688 544 S 0 0.2 0:01.30 init ... So, I'd like to know, experts of serverfault: Do I really need more RAM at the moment? How do they calculate that for 150 simultaneous connections I'd need 3Gb? Thanks for your help!

    Read the article

  • Tracking down rogue disk usage

    - by Amadan
    I found several other questions regarding the theory behind my problem (e.g. this, this), but I don't know how to apply the answers to my machine. # du -hsx / 11000283 / # df -kT / Filesystem Type 1K-blocks Used Available Use% Mounted on /dev/mapper/csisv13-root ext4 516032952 361387456 128432532 74% / There is a big difference between 11G (du) and 345G (df). Where are the remaining 334G? It's not in deleted files. There was only one, it was short, and I truncated it just in case. This is what remains: # lsof -a +L1 / COMMAND PID USER FD TYPE DEVICE SIZE/OFF NLINK NODE NAME zabbix_ag 4902 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4902 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4906 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4906 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4907 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4907 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4908 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4908 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4909 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4909 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4910 zabbix 1w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) zabbix_ag 4910 zabbix 2w REG 252,0 0 0 28836028 /var/log/zabbix-agent/zabbix_agentd.log.1 (deleted) I rebooted to see if fsck does anything. But, from /var/log/boot.log, it seems there are no issues: /dev/mapper/server-root: clean, 3936097/32768000 files, 125368568/131064832 blocks Thinking maybe someone overzealously reserved root space, I checked the master record: # tune2fs -l /dev/mapper/server-root tune2fs 1.42 (29-Nov-2011) Filesystem volume name: <none> Last mounted on: / Filesystem UUID: 86430ade-cea7-46ce-979c-41769a41ecbe Filesystem magic number: 0xEF53 Filesystem revision #: 1 (dynamic) Filesystem features: has_journal ext_attr resize_inode dir_index filetype needs_recovery extent flex_bg sparse_super large_file huge_file uninit_bg dir_nlink extra_isize Filesystem flags: signed_directory_hash Default mount options: user_xattr acl Filesystem state: clean Errors behavior: Continue Filesystem OS type: Linux Inode count: 32768000 Block count: 131064832 Reserved block count: 6553241 Free blocks: 5696264 Free inodes: 28831903 First block: 0 Block size: 4096 Fragment size: 4096 Reserved GDT blocks: 992 Blocks per group: 32768 Fragments per group: 32768 Inodes per group: 8192 Inode blocks per group: 512 Flex block group size: 16 Filesystem created: Fri Feb 1 13:44:04 2013 Last mount time: Tue Aug 19 16:56:13 2014 Last write time: Fri Feb 1 13:51:28 2013 Mount count: 9 Maximum mount count: -1 Last checked: Fri Feb 1 13:44:04 2013 Check interval: 0 (<none>) Lifetime writes: 1215 GB Reserved blocks uid: 0 (user root) Reserved blocks gid: 0 (group root) First inode: 11 Inode size: 256 Required extra isize: 28 Desired extra isize: 28 Journal inode: 8 First orphan inode: 28836028 Default directory hash: half_md4 Directory Hash Seed: bca55ff5-f530-48d1-8347-25c004f66d43 Journal backup: inode blocks The system is: # uname -a Linux server 3.2.0-67-generic #101-Ubuntu SMP Tue Jul 15 17:46:11 UTC 2014 x86_64 x86_64 x86_64 GNU/Linux # cat /etc/lsb-release DISTRIB_ID=Ubuntu DISTRIB_RELEASE=12.04 DISTRIB_CODENAME=precise DISTRIB_DESCRIPTION="Ubuntu 12.04.2 LTS" Does anyone have any tips on what exactly to do to find and hopefully reclaim the missing space?

    Read the article

  • Microsoft signed driver appears as publisher not verfied

    - by Priyanka Gupta
    Task at hand: Microsoft sign drivers on Win 7. I microsoft signed my driver package 3 times every time thinking I might have missed a step or something. However, I cannot seem to get rid of the Windows Security error message "Windows can't verify the publisher of this driver software'. This is not the first time I have signed the driver packages. I was successfully able to sign other driver packages a few months ago. However, with this driver package I keep getting Windows security dialog box. Here's the procedure I follow - Create a new cat file using INF2CAT tool. Self sign the driver using a Versign Class 3 Public Primary Certification Authority - G5.cer. Run the microsoft tests on DTM Servers and clients with the devices that use this driver. Create WLK submission package. Self sign the cab file. Submit the package for certification. The catalog file that comes back after successfully passing tests says Name of signer "Microsoft Windows Hardware Comptibility Publisher". When I check the validity of signature using SignTool, it says the signature is vaild. However, when I try to install the driver with new signed catalog file the windows complain. Any ideas? Edit 11/12/2012: Reply to Eugene's comment Thanks for the help, Eugene. Yes. I did sign two other driver packages before. One of them was modified version of WinUSB driver. I am using the same certificate I used when I signed those two driver packages a few months ago. It costs $250 per signing from Microsoft. I would think that Microsoft would complain about it during certification if the certificate is wrong. I use the following command to self sign the CAT file. I don't have to specify the ceritificate name as there's only one certificate in the directory - Signtool sign /v /a /n CompanyName /t http://timestamp.verisign.com/scripts/timestamp.dll OurCatalogFile.cat Below is the result from running Verify command on the Microsoft signed OurCatalogFile.cat C:\Program Files\Microsoft SDKs\Windows\v7.1\Bin\x64signtool verify /v "C:\User s\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Verifying: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Hash of file (sha1): BDDF39B1DD95881B462164129758A7FFD54F47D9 Signing Certificate Chain: Issued to: Microsoft Root Certificate Authority Issued by: Microsoft Root Certificate Authority Expires: Sun May 09 18:28:13 2021 SHA1 hash: CDD4EEAE6000AC7F40C3802C171E30148030C072 Issued to: Microsoft Windows Hardware Compatibility PCA Issued by: Microsoft Root Certificate Authority Expires: Thu Jun 04 16:15:46 2020 SHA1 hash: 8D42419D8B21E5CF9C3204D0060B19312B96EB78 Issued to: Microsoft Windows Hardware Compatibility Publisher Issued by: Microsoft Windows Hardware Compatibility PCA Expires: Wed Sep 18 18:20:55 2013 SHA1 hash: D94345C032D23404231DD3902F22AB1C2100341E The signature is timestamped: Tue Nov 06 11:26:48 2012 Timestamp Verified by: Issued to: Microsoft Root Authority Issued by: Microsoft Root Authority Expires: Thu Dec 31 02:00:00 2020 SHA1 hash: A43489159A520F0D93D032CCAF37E7FE20A8B419 Issued to: Microsoft Timestamping PCA Issued by: Microsoft Root Authority Expires: Sun Sep 15 02:00:00 2019 SHA1 hash: 3EA99A60058275E0ED83B892A909449F8C33B245 Issued to: Microsoft Time-Stamp Service Issued by: Microsoft Timestamping PCA Expires: Tue Apr 09 16:53:56 2013 SHA1 hash: 1895C2C907E0D7E5C0292B92C6EA8D0E236F525E Successfully verified: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Number of files successfully Verified: 1 Number of warnings: 0 Number of errors: 0 Thank you!

    Read the article

  • Microsoft signed drivers appears as publisher not verfied

    - by Priyanka Gupta
    Task at hand: Microsoft sign drivers on Win 7. I microsoft signed my driver package 3 times every time thinking I might have missed a step or something. However, I cannot seem to get rid of the Windows Security error message "Windows can't verify the publisher of this driver software'. This is not the first time I have signed the driver packages. I was successfully able to sign other driver packages a few months ago. However, with this driver package I keep getting Windows security dialog box. Here's the procedure I follow - Create a new cat file using INF2CAT tool. Self sign the driver using a Versign Class 3 Public Primary Certification Authority - G5.cer. Run the microsoft tests on DTM Servers and clients with the devices that use this driver. Create WLK submission package. Self sign the cab file. Submit the package for certification. The catalog file that comes back after successfully passing tests says Name of signer "Microsoft Windows Hardware Comptibility Publisher". When I check the validity of signature using SignTool, it says the signature is vaild. However, when I try to install the driver with new signed catalog file the windows complain. Any ideas? Edit 11/12/2012: Reply to Eugene's comment Thanks for the help, Eugene. Yes. I did sign two other driver packages before. One of them was modified version of WinUSB driver. I am using the same certificate I used when I signed those two driver packages a few months ago. It costs $250 per signing from Microsoft. I would think that Microsoft would complain about it during certification if the certificate is wrong. I use the following command to self sign the CAT file. I don't have to specify the ceritificate name as there's only one certificate in the directory - Signtool sign /v /a /n CompanyName /t http://timestamp.verisign.com/scripts/timestamp.dll OurCatalogFile.cat Below is the result from running Verify command on the Microsoft signed OutCatalogFile.cat C:\Program Files\Microsoft SDKs\Windows\v7.1\Bin\x64signtool verify /v "C:\User s\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Verifying: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Hash of file (sha1): BDDF39B1DD95881B462164129758A7FFD54F47D9 Signing Certificate Chain: Issued to: Microsoft Root Certificate Authority Issued by: Microsoft Root Certificate Authority Expires: Sun May 09 18:28:13 2021 SHA1 hash: CDD4EEAE6000AC7F40C3802C171E30148030C072 Issued to: Microsoft Windows Hardware Compatibility PCA Issued by: Microsoft Root Certificate Authority Expires: Thu Jun 04 16:15:46 2020 SHA1 hash: 8D42419D8B21E5CF9C3204D0060B19312B96EB78 Issued to: Microsoft Windows Hardware Compatibility Publisher Issued by: Microsoft Windows Hardware Compatibility PCA Expires: Wed Sep 18 18:20:55 2013 SHA1 hash: D94345C032D23404231DD3902F22AB1C2100341E The signature is timestamped: Tue Nov 06 11:26:48 2012 Timestamp Verified by: Issued to: Microsoft Root Authority Issued by: Microsoft Root Authority Expires: Thu Dec 31 02:00:00 2020 SHA1 hash: A43489159A520F0D93D032CCAF37E7FE20A8B419 Issued to: Microsoft Timestamping PCA Issued by: Microsoft Root Authority Expires: Sun Sep 15 02:00:00 2019 SHA1 hash: 3EA99A60058275E0ED83B892A909449F8C33B245 Issued to: Microsoft Time-Stamp Service Issued by: Microsoft Timestamping PCA Expires: Tue Apr 09 16:53:56 2013 SHA1 hash: 1895C2C907E0D7E5C0292B92C6EA8D0E236F525E Successfully verified: C:\Users\logotest\Documents\serialdriversigning\OurCatalogFile.cat" Number of files successfully Verified: 1 Number of warnings: 0 Number of errors: 0 Thank you!

    Read the article

< Previous Page | 114 115 116 117 118 119 120 121 122 123 124 125  | Next Page >